GF Arm-R-Seal TopcoatsView full size

GF Arm-R-Seal Urethane Topcoats

General Finishes

Reference: GF

Arm-R-Seal topcoats are made with only the highest quality urethane resin, making them extremely durable and long lasting. They are formulated to be wiped on with a cloth or applied with a foam brush, thus eliminating drips and sags. They penetrate to provide deep down protection and that "natural" look.
Visit the General Finishes Design Center OR Pinterest Board for more furniture finishing ideas.

More details

Customer Testimonials

I love Wood You Furniture! And they can paint/stain it any colour for you, as well as take it to the mail boat.

- Dusty T.

Availability:Although we try to keep these items in stock, from time to time it may be necessary to special order at additional time and UPS shipping expense. If you need this asap, please inquire before purchasing.

Got Questions?

quantity upquantity down

$22.44 VAT Incl.$


Arm-R-Seal is a heavy duty oil and urethane oil base top coat, which produces a beautiful hand rubbed quality finish.

Sheens: Satin, semi-gloss and gloss sheens.
Sanding: On bare wood sand to 150 or 180. Can be wet sanded into the wood using 400-600 grit. Wipe off excess after sanding.
Sealer: General Finishes Seal A Cell Clear, Pre-stain Natural Conditioner, or can be used as a self sealing finish. Can also be used over Danish Oil, Lin- seed Oil & Tung Oil once they are dry.
Color tone: Warm amber tone. This finish will continue to darken over time.
Application: Wipe on with a cloth, natural bristle brush, foam brush, paint pad applicator, or spray*
Coats: Minimum 3 coats, additional coats can be applied
Dry time to touch: 1-2 hours
Dry time to recoat: 12-24 hours. Allow more dry time if it is humid
Dry time for light use: 72 Hours

Cure time: 30 days

Cleanup: Mineral Spirits
 
Coverage: 200 sq. ft/qt
Size: Pints, Quarts, Gallons 
VOC: < 575grams/liter
Recommended uses: Windows, bookcases, wall shelves, furniture, toys, ta- bles, dressers, stools, millwork, doors.

*Spraying Arm-R-Seal:

Arm-R-Seal can be sprayed successfully, but we prefer hand application methods because it is very easy to spray too much in one area. If you choose to spray, use very thin coats and watch for runs (large drips that run down the side of your project). If you notice a run, immediately wipe or brush it out. If you correct a run promptly, you will not see a mark. However, dried runs can be difficult to remove. Important: Wear a mask and work in a well ventilated spray booth. Size: Small Needle Nozzle (1mm) 


WARNING: TEST FOR COMPATIBILITY WHEN USING THIS PRODUCT WITH PRODUCTS FROM OTHER BRANDS. General Finishes products should be tested to your complete satisfaction before using. General Finishes will not be responsible for any failure if our products are used in conjunction with other brands of finishes. We do not test General Finishes products with those of another manufacturer and will not accept liability if there is a compatibility issue.

WATER SPILLS AND DAILY USE: Clean water spills up as they occur during regular use and protect from heat. Although General Finishes products are water resistant, they are not impervious to water. Surfaces will not be damaged by spilled water so long as it is cleaned up promptly. We recommend using coasters to protect your wood from standing water and pot holders to protect from heat.

  • Made in the USA: Yes

No customer comments for the moment.

Write your review

GF Arm-R-Seal Urethane Topcoats

GF Arm-R-Seal Urethane Topcoats

Arm-R-Seal topcoats are made with only the highest quality urethane resin, making them extremely durable and long lasting. They are formulated to be wiped on with a cloth or applied with a foam brush, thus eliminating drips and sags. They penetrate to provide deep down protection and that "natural" look.
Visit the General Finishes Design Center OR Pinterest Board for more furniture finishing ideas.

Write your review

NO registration required!

If the question you have has not yet been answered here, use the form below to ask something about this addon.

(optional)
*(Required to be notified when an answer is available)
Send question!

11 other products in the same category:

Send a message

GF Arm-R-Seal Urethane Topcoats

Arm-R-Seal topcoats are made with only the highest quality urethane resin, making them extremely durable and long lasting. They are formulated to be wiped on with a cloth or applied with a foam brush, thus eliminating drips and sags. They penetrate to provide deep down protection and that "natural" look.
Visit the General Finishes Design Center OR Pinterest Board for more furniture finishing ideas.